Autopsy of a FRITZ!Powerline 546E adapter
Hardware Details:
| Architecture: |
MIPS |
| Vendor: |
Atheros |
| Bootloader: |
Eva_AVM |
| System-On-Chip: |
Atheros AR9344 |
| CPU Speed: |
560 Mhz |
| Flash-Chip: |
Macronix
MX25L12845EMI-10G |
| Flash size: |
16 MiB |
| RAM: |
64 MiB (Winbond
W9751G6KB-25) |
| Wireless: |
AR7420
|
| Ethernet: |
AR7420
|
| Powerline: |
AR7420
|
Smart Metering:
|
Prolific
PL8331 |
| Serial: |
yes
|
| JTAG: |
unknown |
Photos:
[Link]
Serial Console:
The parameters are: 115200 baud, 8N1
The pin header has default AVM layout, that means GND, TxD, RxD where GND is located near the ethernet jacks (bottom of device).
Console Transcript of original firmware:
[-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-]
(AVM) EVA Revision: 1.1437 Version: 2437
(C) Copyright 2005 AVM Date: Aug 8 2012 Time: 16:29:53 (0) 2 0x0-0x240D
[FLASH:] MACRONIX Uniform-Flash 16MB 256 Bytes WriteBuffer
[FLASH:](Eraseregion [0] 256 sectors a 64kB)
[SYSTEM:] AR9344 on 560/450/225MHz *
Eva_AVM >help
Commands Description
-------- -----------
help help
dm dump mem 32 Bit
cm change mem 32 Bit
dh dump mem 16 Bit
ch change mem 16 Bit
db dump mem 8 Bit
cb change mem 8 Bit
erase Erase Flash
printenv print Env. Variables
restart reboot Device
setenv set Env. variable
unsetenv unset Env. variable
go load & start kernel from mtd1
setmac set mac addresses (like 12:23:40)
mdio-read32 read 32-Bit mdio value
mdio-write32 write 32-Bit mdio value
mdio-read read 16-Bit mdio value
mdio-write write 16-Bit mdio value
eth-status eth Status
Eva_AVM >printenv
HWRevision 190
HWSubRevision 1
ProductID Fritz_Box_HW190
SerialNumber 0000000000000000
annex Ohne
autoload yes
bootloaderVersion 1.1437
bootserport tty0
cpufrequency 560000000
firstfreeaddress 0x810FCFE8
firmware_info 118.05.50
firmware_version avm
flashsize nor_size=0x0 sflash_size=16MB nand_size=0MB
maca 24:65:11:xx:xx:xx
macb 24:65:11:xx:xx:xx
macwlan 24:65:11:xx:xx:xx
macdsl 24:65:11:xx:xx:xx
memsize 0x04000000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
modulemem 2040826
mtd1 0x9F020000,0x9FF00000
mtd2 0x9F000000,0x9F020000
mtd3 0x9FF00000,0x9FF80000
mtd4 0x9FF80000,0xA0000000
my_ipaddress 192.168.178.1
plc_dak_nmk xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx-xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx
prompt Eva_AVM
req_fullrate_freq 225000000
sysfrequency 225000000
urlader-version 2437
usb_board_mac 24:65:11:xx:xx:xx
usb_device_id 0x0000
usb_device_name USB DSL Device
usb_manufacturer_name AVM
usb_revision_id 0x0000
usb_rndis_mac 24:65:11:xx:xx:xx
wlan_key xxxxxxxxxxxxxxxxxxxx
Eva_AVM >go
.....................................[prom_init]:
[ath_init_cmdline]:
[ath_init_cmdline]: argv[0] = 'go'
[ath_init_cmdline]: argv[1] = 'console=ttyS0,115200n8r'
[ath_init_cmdline]: argv[2] = 'nor_size=0x0 sflash_size=16MB nand_size=0MB'
[ath_init_cmdline]:commandline = 'console=ttyS0,115200n8r nor_size=0x0 sflash_size=16MB nand_size=0MB ethaddr=24:65:11:xx:xx:xx'
[prom_init]: call env_init
[prom_init]: call set_wlan_dect_config_address
[prom_init]: done
[plat_mem_setup]:
[plat_mem_setup]: "memsize" "0x04000000"
[plat_mem_setup]: memsize 0x4000000
Booting Atheros AR934x
[ 0.000000] Linux version 2.6.32.41 (gcc version 4.6.3 (Buildroot 2011.11) ) #1 Wed Jan 23 11:41:12 CET 2013
[ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] [plat_mem_setup] memsize 0x4000000
[ 0.000000] Determined physical RAM map:
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] [module-alloc] failed 0x1f23fa bytes at 0x81081000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200n8r nor_size=0x0 sflash_size=16MB nand_size=0MB ethaddr=24:65:11:xx:xx:xx
[ 0.000000] [parse_mtd_size] 16777216
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] wait instruction: r4k_wait_irqoff
[ 0.000000] [avm_cache_set_coherency]: setting cache coherency for HWRevision=190 to write back allocate
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] [mips_nmi_setup] setup NMI vector to base 0x80000380
[ 0.000000] Memory: 57396k/65536k available (3646k kernel code, 8068k reserved, 1312k data, 152k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] [mips_cpu_irq_init] irq_base 0
[ 0.000000] [ath_gpio_irq_init] done
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] console [ttyS0] enabled
[ 0.004000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[ 0.104000] Mount-cache hash table entries: 512
[ 0.108000] kernel_init: started
[ 0.108000] kernel_init: kernel locked
[ 0.112000] NET: Registered protocol family 16
[ 0.116000] [ath_avm_gpio_init]
[ 0.120000] [avmnet] [avmnet_cfg_init] Driver version: 6.54.1.4 - Revision 1715:2036 - Mi 23.01.2013 11:40:48
[ 0.124000] [ath_mtd_init]
[ 0.124000] [ath_mtd_init] flash: type=512, start=0x1f000000, end=0x20000000
[ 0.128000] [find_nmi_vector] nmi vector found. Firmware length 0x8ec523 bytes (erase block align 0x8f0000) vector gap size 0x1000 bytes.
[ 0.132000] [find_nmi_vector] add 'urlader' size 0x20000 to length
[ 0.136000] bio: create slab at 0
[ 0.140000] SCSI subsystem initialized
[ 0.144000] usbcore: registered new interface driver usbfs
[ 0.148000] usbcore: registered new interface driver hub
[ 0.152000] usbcore: registered new device driver usb
[ 0.156000] NET: Registered protocol family 2
[ 0.160000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.168000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.172000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.180000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.188000] TCP reno registered
[ 0.192000] NET: Registered protocol family 1
[ 0.196000] RPC: Registered udp transport module.
[ 0.200000] RPC: Registered tcp transport module.
[ 0.204000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.212000] ATH GPIOC major 0
[ 0.216000] [simple_profiling] 0 entries 50 min
[ 0.220000] squashfs: version 3.4 (2008/08/26) Phillip Lougher
[ 0.228000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.232000] fuse init (API version 7.13)
[ 0.236000] msgmni has been set to 112
[ 0.256000] alg: No test for stdrng (krng)
[ 0.308000] io scheduler noop registered (default)
[ 0.312000] [avm_membench_init]
[ 0.316000] avm_net_trace: Up and running.
[ 0.324000] [loadcontrol] set auto - scale=1
[ 0.328000] [avm] configured: watchdog event debug enable direct gpio
[ 0.332000]
[ 0.336000] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Jan 23 2013 11:40:22)
[ 0.348000] [simple-profiling]: 4 performance counters implemented
[ 0.352000] Enable Performance Counter 0 for (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable)
[ 0.364000] [simple-profiling]: 4 performance counters implemented
[ 0.372000] Enable Performance Counter 1 for (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable)
[ 0.384000] [avm]: AVM Simple Profiling enabled.
[ 0.388000] ttyS0 at MMIO 0x18020000 (irq = 19) is a PORT_16550A
[ 0.396000] ttyS1 at MMIO 0x18500000 (irq = 22) is a PORT_ATH_HI
[ 0.400000] Generic platform RAM MTD, (c) 2004 Simtec Electronics
[ 0.408000] Registering AR7240-flash-driver...
[ 0.412000] [ath_jffs2_parser_function] mtd_info->name ath-nor mtd_info->index 0 param=0 p_mtd_pat=0x8381bda0
[ 0.424000] [ath_jffs2_parser_function] try partition kernel (offset 0x20000 len 15597568)
[ 0.432000] [ath_squashfs_parser_function] mtd_info->name ath-nor mtd_info->index 0 param=0 p_mtd_pat=0x8381bda0
[ 0.444000] [ath_squashfs_parser_function] *p_mtd_pat->name filesystem
[ 0.452000] [ath_squashfs_parser_function] try partition kernel (offset 0x20000 len 15597568 blocksize=10000) read='ar7240_flash_read+0x0/0x200'
[ 0.532000] [ath_squashfs_parser_function] magic found @pos 0x192000
[ 0.536000] [ath_squashfs_parser_function] flashsize=0
[ 0.544000] [ath_squashfs_parser_function] jffs2_start@ea0000 size: 6
[ 0.600000] [0]system-load 1 20 tasks:0 % curr:swapper(0 %) max:swapper(0 %, pid:1), readytorun: 1, pgfault 0/s (max 0 avg 0.0)
[ 3.040000] 6 find_squashfs partitions found on MTD device ath-nor
[ 3.044000] Creating 6 MTD partitions on "ath-nor":
[ 3.048000] 0x000000192000-0x000000f00000 : "rootfs"
[ 3.056000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 3.068000] 0x000000020000-0x000000192000 : "kernel"
[ 3.072000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 3.088000] 0x000000000000-0x000000020000 : "urlader"
[ 3.092000] 0x000000f00000-0x000000f80000 : "tffs (1)"
[ 3.100000] 0x000000f80000-0x000001000000 : "tffs (2)"
[ 3.104000] 0x000000ea0000-0x000000f00000 : "jffs2"
[ 3.108000] tun: Universal TUN/TAP device driver, 1.6
[ 3.116000] tun: (C) 1999-2004 Max Krasnyansky
[ 3.120000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.128000] CAPI Subsystem Rev 1.1.2.8
[ 3.132000] AVM PA 3.1.1 2012-11-28
[ 3.136000] AVM PA skb pktinfo at offset 128 size 192
[ 3.140000] [loadcontrol]module avm_pa registered
[ 3.148000] TCP cubic registered
[ 3.148000] mcfw: IGMPv3 fast forwarding
[ 3.152000] NET: Registered protocol family 10
[ 3.160000] NET: Registered protocol family 17
[ 3.164000] ath_otp_init: Registering OTP success
[ 3.168000] ath_clksw_init: Registering Clock Switch Interface success
[ 3.176000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
[ 3.184000] mount on mtd3 and mtd4 (double buffering)
[ 3.188000] Adam2 environment variables API installed.
[ 3.196000] {avmnet_cfg_netinit}
[ 4.160000] [avmnet_set_macaddr] Setup Mac Addr for Device(plc): 24:65:11:xx:xx:xx
[ 4.172000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 24:65:11:xx:xx:xx
[ 4.180000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 24:65:11:xx:xx:xx
[ 4.188000] kernel_init: basic setup done
[ 4.196000] [squashfs] use lzma compression
[ 4.200000] VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
[ 4.208000] Freeing unused kernel memory: 152k freed
[ 4.224000] trying /sbin/init
starting pid 100, tty '/dev/ttyS0': '/etc/init.d/rc.S'
tar: removing leading '/' from member names
source files in group 0 ...
/etc/init.d/S00-signal /etc/init.d/S02-led /etc/init.d/S08-tffs
/etc/init.d/S01-head /etc/init.d/S05-watchdog /etc/init.d/S09-config
[ 4.836000] TFFS Name Table K
[ 5.748000] [module-alloc-by-name] give 0x12000 bytes at 0x81081000 to module 'led_modul_Fritz_Box_HW190'
[ 5.760000] led_modul_Fritz_Box_HW190: module license '
[ 5.760000] (C) Copyright 2012 by AVM
[ 5.760000] ' taints kernel.
[ 5.772000] Disabling lock debugging due to kernel taint
[ 5.788000] [LED] use GPIO 17 for 'gpio_avm_led_power'
[ 5.792000] [LED] use GPIO 13 for 'gpio_avm_led_wlan'
[ 5.800000] [LED] use GPIO 19 for 'gpio_avm_led_plc'
[ 5.804000] [LED] use GPIO 4 for 'gpio_avm_prolific_ac_mode'
[ 5.808000] [LED] use GPIO 15 for 'gpio_avm_prolific_ac_reset'
[ 5.816000] [BUTTON] use GPIO 21 for 'gpio_avm_button_wlan'
[ 5.820000] [BUTTON] use GPIO 14 for 'gpio_avm_button_power'
[ 5.828000] [BUTTON] use GPIO 16 for 'gpio_avm_button_plc'
[ 5.832000] [button_init] name button_both, virtual multipush button
[ 5.848000] AVM_WATCHDOG: System Init UEberwachung 120 Sekunden
mknod: /var/flash/ar7.cfg: File exists
P-Defaults: do nothing
exceute files in group 0 ...
/etc/init.d/E05-basemodules
group 0 done ...
source files in group 1 ...
/etc/init.d/S10-html /etc/init.d/S12-default
/etc/init.d/S10-vm /etc/init.d/S15-filesys
/etc/init.d/S11-config_def /etc/init.d/S17-tam
exceute files in group 1 ...
/etc/init.d/E15-device
mknod led c 249
mknod tffs c 250
mknod avm_power c 254
mknod debug c 251
mknod avm_event c 252
mknod capi_oslib c 68
/
group 1 done ...
source files in group 2 ...
/etc/init.d/S21-udev
exceute files in group 2 ...
group 2 done ...
source files in group 3 ...
/etc/init.d/S30-ledcfg /etc/init.d/S35-rext
Jan 1 01:00:06 udevd[285]: specified group 'tty' unknown
Jan 1 01:00:06 udevd[285]: specified group 'dialout' unknown
Jan 1 01:00:06 udevd[285]: specified group 'kmem' unknown
Jan 1 01:00:06 udevd[285]: specified group 'video' unknown
Jan 1 01:00:06 udevd[285]: specified group 'audio' unknown
Jan 1 01:00:06 udevd[285]: specified group 'lp' unknown
Jan 1 01:00:06 udevd[285]: specified group 'disk' unknown
Jan 1 01:00:06 udevd[285]: specified group 'floppy' unknown
Jan 1 01:00:06 udevd[285]: specified group 'cdrom' unknown
Jan 1 01:00:06 udevd[285]: specified group 'tape' unknown
[ 7.356000] [module-alloc-by-name] give 0x28000 bytes at 0x81093000 to module 'krextdmod'
[ 7.392000] krextd: init start (Jan 23 2013 13:13:57)
[ 7.396000] krextd: periodic_usec set to 580000
[ 7.400000] krextd: init done
exceute files in group 3 ...
group 3 done ...
source files in group 4 ...
/etc/init.d/S40-swap /etc/init.d/S44-hostname /etc/init.d/S48-configd
/etc/init.d/S42-ptest /etc/init.d/S46-usb
[ 7.480000] [module-alloc-by-name] give 0x1000 bytes at 0x810bb000 to module 'lzo_compress'
[ 7.500000] [module-alloc-by-name] give 0x1000 bytes at 0x810bc000 to module 'lzo_decompress'
[ 7.552000] [module-alloc-by-name] give 0x5000 bytes at 0x810bd000 to module 'ramzswap'
[ 7.596000] ramzswap: /dev/ramzswap0 initialized: disksize_kb=8192mknod: /dev/ramzswap0: File exists
[ 7.632000] Adding 8184k swap on /dev/ramzswap0. Priority:-1 extents:1 across:8184k SS
exceute files in group 4 ...
/etc/init.d/E46-net
/etc/init.d/E46-net: line 5: /etc/init.d/rc.dsl.sh: not found
Jan 1 01:00:08 rextd[344]: startup (Jan 23 2013 13:13:38)
Jan 1 01:00:08 rextd[349]: rextd.with_plc_flt = 1
[ 8.300000] krextd: krextd_ioctl got cmd=0x80045205 arg=0x0
[ 8.304000] krextd: trace switched off
Jan 1 01:00:08 [ 8.324000] krextd: krextd_ioctl got cmd=0x80085280 arg=0x7ffd46a0
rextd[349]: set_plc_bridge_flt: plc:ifindex=3
rc.wlan: Start WLAN...
Jan 1 01:00:08 rextd[349]: interface eth0 setup.
[ 8.356000] device eth0 entered promiscuous mode
WLAND:[00355]:01:00.08:Build = Jan 23 2013 13:44:13
group 4 done ...
source files in group 5 ...
exceute files in group 5 ...
group 5 done ...
source files in group 6 ...
exceute files in group 6 ...
group 6 done ...
source files in group 7 ...
/etc/init.d/S73-capitcp /etc/init.d/S76-media
/etc/init.d/S75-inetd /etc/init.d/S78-aha
killall: aha: no process killed
[ 8.868000] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 01:00:08 [ 8.876000] device eth1 entered promiscuous mode
rextd[349]: interface eth1 setup.
Jan 1 01:00:09 ctlmgr[345]: REXT_Register called
[ 9.188000] eth: port 0 status 2 throttle 0
[ 9.196000] eth: port 1 status 1 throttle 1
[ 9.408000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 9.412000] eth: port 2 status 1 throttle 1
[ 9.416000] [avmnet] [avmnet_power_config] tried to set mode for port 2
[ 9.424000] [avm_power] : ethernet switch failed
Jan 1 01:00:09 rextd[349]: DHCPC: lan: state in[ 9.436000] eth: port 3 status 1 throttle 1
it
Jan 1 01:0[ 9.440000] [avmnet] [avmnet_power_config] tried to set mode for port 3
0:09 rextd[349]: 9.448000] [avm_power] : ethernet switch failed
DHCPC: lan set default ip address
Jan 1 01:00:09 rextd[349]: DHCPC: lan: state init, got event discover-sent
Jan 1 01:00:09 rextd[349]: DHCPC: lan: state selecting
Jan 1 01:00:09 rextd[349]: DHCPC on lan started
Jan 1 01:00:09 rextd[349]: DHCP state: client
Jan 1 01:00:09 ctlmgr[345]: WLANLIB: my_wlan_init:487: svn revision 1283
Jan 1 01:00:10 ctlmgr[345]: WLANLIB: weak_wlan_check:57: Missing weak 'process_wlanmail'.
Jan 1 01:00:10 ctlmgr[345]: REXT_Register called
[aha: avm_home_global_save_do_restore][ 10.908000] [uart_avm_ath_hi_set_baudrate/423] set baudrate to '9600' baud clock '9600' serial clock '100000000'
Error: no data [ 10.920000] [uart_avm_ath_hi_set_baudrate/423] set baudrate to '9600' baud clock '9600' serial clock '100000000'
in '/var/flash/ahaglobal.cfg'
Jan 1 01:00:11 rextd[432]: already running
rc.wlan: Start WLAN...
rc.wlan: WLAN daemon already running
exceute files in group 7 ...
group 7 done ...
source files in group 8 ...
/etc/init.d/S85-apps
exceute files in group 8 ...
/etc/init.d/E80-bootplc
group 8 done ...
source files in group 9 ...
/etc/init.d/S99-tail
run_clock demon [ 11.840000] AVM_WATCHDOG: System Init UEberwachung abgeschlossen (285030 ms noch verfuegbar)
started
[ 11.884000] SysRq : Changing Loglevel
[ 11.884000] Loglevel set to 4
[AHA] SIGHUP received
[AHA] SIGHUP received
[aha: prolific_handle_com] Error: message received (ret=-1, errno 4, 'Interrupted system call')
[AHA] SIGHUP received
[aha: avm_home_button_thread] Error: message received (ret=-1, errno 4, 'Interrupted system call')
[AHA] SIGHUP received
[aha: avm_home_upper_connection_thread] Error: message received (ret=-1, errno 4, 'Interrupted system call')
[AHA] SIGHUP received
Please press Enter to activate this console. Jan 1 01:00:12 rextd[349]: DHCPC: lan: state selecting, got event timeout
Jan 1 01:00:12 rextd[349]: DHCPC: lan: state selecting, got event discover-sent
starting pid 467, tty '/dev/ttyS0': '-/bin/sh'
BusyBox v1.19.3 (2012-08-08 13:13:47 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
ermittle die aktuelle TTY
tty is "/dev/ttyS0"
Serielles Terminal
# psJan 1 01:00:19 rextd[349]: DHCPC: lan: state selecting, got event timeout
Jan 1 01:00:19 rextd[349]: DHCPC: lan: state selecting, got event discover-sent
PID USER VSZ STAT COMMAND
1 root 1236 S init
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [events/0]
5 root 0 SW [khelper]
8 root 0 SW [async/mgr]
15 root 0 SW [sync_supers]
16 root 0 SW [bdi-default]
18 root 0 SW [kblockd/0]
23 root 0 SW [ksuspend_usbd]
27 root 0 SW [khubd]
32 root 0 SW [rpciod/0]
37 root 0 SW [kswapd0]
38 root 0 SWN [ksmd]
39 root 0 SW [aio/0]
40 root 0 SW [nfsiod]
42 root 0 SW [crypto/0]
63 root 0 SW [pm_info]
70 root 0 SWN [avmdebug]
75 root 0 SW [mtdblockd]
86 root 0 SW [kondemand/0]
93 root 0 SW [tffsd_mtd_0]
94 root 0 SW [avmnet_workqueu]
99 root 0 SW [avmnet_timer]
159 root 0 SW [cleanup_timer_f]
289 root 1236 S < /sbin/udevd --daemon
290 root 1236 S < /sbin/udevd --daemon
309 root 1236 S < /sbin/udevd --daemon
327 root 2452 S /bin/configd
345 root 7732 S ctlmgr
349 root 3288 S rextd -v
357 root 3452 S wland -B
364 root 1236 S /usr/sbin/inetd
375 root 7732 S ctlmgr
376 root 7732 S ctlmgr
377 root 7732 S ctlmgr
385 root 7732 S ctlmgr
386 root 7732 S ctlmgr
389 root 2464 S /usr/bin/aha
407 root 2464 S /usr/bin/aha
408 root 2464 S /usr/bin/aha
409 root 2464 S /usr/bin/aha
410 root 2464 S /usr/bin/aha
411 root 2464 S /usr/bin/aha
453 root 1240 S sh /etc/init.d/E80-bootplc
455 root 1224 S sleep 20
458 root 1136 S /bin/run_clock -c /dev/tffs -d
467 root 1244 S -/bin/sh
504 root 1232 R ps
#